How To Build A Firewood Holder In 7 Quick Easy Steps!

If you happen to’re in search of a spot to retailer your firewood that is also tremendous cool to have a look at, take a look at this firewood holder DIY. Earlier than, I’d simply have my totally different sizes piled up in containers across the fireside, which was actually unattractive. So on a whim I threw these collectively. The three compartments permit me to separate small, from medium, to giant items of wooden. Seize a set of plans and let me present you the way I construct them.

Let’s Construct A Firewood Holder

DIY Firewood Holder Plans

$9.99

I’ve created a set of plans to make constructing this firewood holder fast and straightforward!

Supplies I Used on this Construct:

Step 1: Deciding on Materials and Chopping to Dimension

I did design and construct these on a whim so when choosing materials, I simply seemed round my store to see what I had already that might match the sizes. I discovered this stack of three/4” minimize off from some cabinets I tore a component that I’ll make the physique from. Then for the again, I’ve some 1/2” plywood from who is aware of what.

I began off by ripping the sheets all the way down to width wanted. If you need precise dimensions, I’ve a set of plans out there over on my web site. I tilted the blade over to then minimize within the angles wanted to created the pointed miters. Since there are lots of repeated elements, I arrange a cease block in order that I might make all of them the identical. Once you do that, you need to make certain to set the cease block again far sufficient so the board gained’t be touching it when it contacts the blade. As that is what may cause chill.

To save lots of from switching the blade backwards and forwards, after reducing one facet with the wanted angle, I’d flip the board and minimize the opposite facet because it nonetheless had a 90 on one finish. This can go away the remaining board with angles on each finish, that I can chop up for the mitered elements. I personally wish to at all times do a check first and a dry match to verify issues are going to work as I’ve them deliberate. That appears good although.

Step 2: Banding the Edges of the Firewood Holder

Now I simply wanted 12 of them whole so I locked within the new distance for the fence for this half and chopped up the remaining bit into items.

This undertaking solely consist of 4 totally different elements. What I’ll name the facet, the tops that are barely longer than anything, the horizontal cabinets, then the mitered factors. Understand that it will be easy so as to add extra to subtract the variety of cubbies, relying in your areas wants.

Alrighty, now I’ll edge band the perimeters that will likely be dealing with the entrance. Really, on second thought, I like the thought of portray them as a substitute. Observe: that if you happen to edge band you’ll want to try this earlier than becoming a member of the elements collectively, however if you wish to paint, then you possibly can go straight into assembling.

Step 3: Assembling the Firewood Holder Cubicles

For assembling, I began off on high of my workbench and what I did is apply some wooden glue, I’m utilizing DAPs weldwood right here, to each joint, then pin nailed issues collectively utilizing my 23 gauge nailer. This can be a fairly weak joint till the wooden glue has time to arrange, so I used to be being cautious as I used to be shifting it round to connect the subsequent leg. If I didn’t have a 23 gauge, I’d have used a 18 gauge as a substitute.

After getting a couple of hooked up, I assumed it will make issues simpler to do it on the bottom so I might see every little thing clearly as I used to be attaching legs. So I moved it all the way down to the ground and continued. I’d juke and jive to create the factors of the cubbies, then connect the horizontal that may create the separation between.

I paused once I acquired to the very high as a result of the best way I’ve it designed, the highest edge will really be seen. With that, I edge banded each of those elements earlier than including them on. This is so simple as heating up an iron and warming up the glue on the again of the banding till it sticks to the plywood edge. This will likely be barely totally different than the ply, however it doesn’t hassle me.

Step 4: Portray the Firewood Holder Cubbies

 I left that the place it sat to present that glue time to arrange and dry. Whereas it was, I grabbed items that may make up the again from my 1/2” plywood scraps. I additionally grabbed the items that may make up the perimeters. I would like each of those to be painted the identical shade as my wall which implies I would like to present them a couple of coats earlier than attaching the cubbies.

Since I’ve the paint out, I additionally wished to color that entrance fringe of the cubbies. I first give them each sanding to get them clean. Now when working with plywood, there are sometimes voids on each single edge. In an effort to get a clean trying paint floor, I apply some wooden filler on a putty knife. I’m utilizing DAP Premium wooden filler. These things not solely dries quick however is straightforward to sand and is nice to paint match in case you are staining one thing.

After letting it dry for about 30 minutes, I got here again with a sanding sponge to knock it down flat in order that I might roll on the paint onto the items of the firewood holder.

With ending out of the best way, let me simply push this button right here to boost my ending shelf up and find the {hardware} I’ll want to connect the cubbies to the again.

Step 5: Shaping the Again to Match the Firewood Holder Cubbies

I began with a again barely bigger than what I wanted, then plopped the cubbies down onto it and lined it up in order that the underside cubby was flush to the top of the plywood. I used my pin nailer to only tack issues in place to begin. The top is straightforward accurately flush, however to verify the remainder weren’t crocked, I pulled a tape to get the spacing good earlier than tacking the remainder. With it not capable of fall off now, I tilted your entire unit on it’s face in order that I’d have entry to the underside to throw in screws. Right here, I made certain to pre drill to forestall splitting.

Step 6: Securing the Firewood Holder Cubbies to the Again

The highest location is straightforward to find as a result of you may have a visible on the place the shelf is positioned. Nonetheless, the second is difficult as a result of it’s in the midst of nowhere. What I do is seize a pace sq., this Crescent one has an extra 6” flip out rule in order that I can place it within the middle of the shelf, go all the way down to the dimension wanted, and pre drill. If you happen to don’t have this pace sq. or one other lengthy one, then a stage would additionally do the trick.

For the angled portion of the cabinets, the pace sq. wouldn’t work, so I grabbed a scrap and minimize in an angle on the tip. This fashion I might relaxation it on the shelf and permit me to mark the peak. Ensuring to maintain it in the identical location, I moved the scrap to the face closest to me to now drop it down again to the road I made which supplies me the situation of the angled shelf to pre drill and connect a screw.

With the again on, this factor now feels actually safe and robust. I flipped it up to have a look. I really suppose it appears to be like fairly good with a sq. again on it and was contemplating leaving it as is however then I made a decision to stay to my authentic plan and make the again flush to the geometric form. I wasn’t capable of find my palm router, which is definitely the best software to trim the again off, so as a substitute I put a flush trim bit in my router desk and trim it off that method. The important thing right here is to maintain the unit good and flush on the desk as you progress it alongside.

I laid the unit over and hooked up the facet. This can assist assist the horizontal cabinets that may really be supporting the load of the firewood.

Step 7 : Putting in the Firewood Holder and Chopping Firewood

 Very last thing to do was set up them. Now I personally wished mine up off the bottom so I wouldn’t block an outlet I’ve over on the appropriate hand facet. Then I additionally like to make use of this space for storing my video games and puzzles. With that, I propped the items up, discovered the studs, then drove a couple of screws into the again of the unit to connect them.

Okay lets load it down and see how a lot it may possibly maintain. Now that, is a lot better than earlier than. As an alternative of ugly containers and totes, I now have a pleasant firewood holder with devoted area for the wooden. This can permit me room to retailer and separate all totally different sizes of firewood throughout winter. Then I personally just like the look of wooden sufficient to maintain it full 12 months spherical, however I might additionally retailer different kinds of nicknacks throughout spring and summer season ought to I need to.

What do y’all take into consideration them? Keep in mind how straightforward it’s to make bigger or smaller. I even suppose they might look good horizontal, relying in your area. I’ve a set of plans for this undertaking in addition to many different over on my web site. Actually, if you need firewood storage concepts, I’ve a couple of of them.

I’ll see you subsequent time.

Materials I Used For This Construct: